The JMR Manual Tube Bender (TBM-250) bends round tube, square tube and pipe in mild steel, DOM, 4130 chromoly, stainless, Docal and aluminum. It uses the same bender head as our hydraulic benders, so the frame can handle more than most people can pull. That's why we rate it by what an average person can realistically bend by hand: 2" OD x .120" wall round tube and 2" x .120" wall square tube. Add a hydraulic upgrade kit later and it bends up to 2-1/2" OD. See our capacity charts for full size and wall ratings.

FIVE DRIVE SPEEDS

The TBM-250 has more than 2x leverage than any other manual bender. The ratchet runs on bronze bushings. Use a higher gear to move quickly through small tube, or drop into low gear for 2" and heavy-wall material. An average person can bend 90° in 1.5" tube in 60 seconds.

BEND 90° WITHOUT RE-PINNING

The long drive rack makes a full 90° bend in one pass, and the bender is capable of bends up to 180°. A degree wheel with an adjustable pointer is included. Zero it to your setup for accurate, repeatable angles from part to part.

CENTER PIVOT BUSHINGS

The pivots run on self-lubricating Delrin bushings, so the arms stay in place when the die comes out. Changing dies means pulling one pin. Arms are high-tensile plate. Pins are heat-treated 4140 alloy.

UPGRADE TO HYDRAULIC ANY TIME

Because the bender head matches our hydraulic benders, converting is easy. Choose the Air/Hydraulic Upgrade Kit with a foot pump, or the Electric/Hydraulic Upgrade Kit. Either one raises capacity to 2-1/2" OD and takes the pulling out of heavy-wall work.

MADE IN USA, STOCKED IN PASO ROBLES

We build and stock the TBM-250 in our Paso Robles, California shop, so it ships from inventory instead of a lead-time list. It mounts on a bench, a floor stand or a receiver hitch. Die sets, the handle and mounting are sold separately, or get a complete setup with dies in our Bender Packages. Questions about your tube size or project? Call (805) 239-5972 or email info@jmrmfg.com

TBM-250 INSTRUCTION MANUAL

Manual Tube Bender (TBM-250) specifications
Capacity
By hand 2" .120" tube, 2" .120" square
With hydraulic upgrade Up to 2-1/2" .120" wall OD tube
Shapes Round tube, square tube and pipe
Materials Chromoly, stainless, mild steel and aluminum
Bending
Bend capacity 180°
Drive Manual, 5 speeds
90° bend Without re-pinning the die
Hydraulic upgrade Available at any time
Die sets All JMR tube, pipe and square die sets
Construction
Arms High-tensile steel
Pins Heat treated 4140
Pivot Delrin pivot bushings
Ratchet Bronze bushings
Finish Powder-coated arms, rack and clevis
Size and support
Shipping weight 50 lb
Dies Sold separately
Model TBM-250
Made in Paso Robles, California, USA
Warranty 1-year limited

How is it different from the RaceLine Tube Bender?
This bender has 5 speeds instead of 3, a longer rack that bends 90 degrees without re-pinning the die, bronze bushings in the drive mechanism, and a full powder coat. The RaceLine is the lower-cost version with uncoated arms and rack. Both are made in the USA.
What can I bend by hand?
Up to 2" OD tube. It bends round tube, square tube and pipe in chromoly, stainless, mild steel and aluminum.
Can I make a 90 degree bend without re-pinning?
Yes. The longer rack makes a full 90 degree bend without re-pinning the die.
Can I upgrade it to hydraulics later?
Yes, at any time. The Air/Hydraulic and Electric/Hydraulic Upgrade Kits add a cylinder, pump and hoses, and raise capacity to 2-1/2".
Are dies included?
No. Die sets are sold separately, so you only buy the sizes you need. Any JMR tube, pipe or square die set fits this bender.
What warranty does it come with?
A 1-year limited warranty.

Need dies?

Dies are sold separately, so you only buy the sizes you need. Every JMR die fits every JMR bender, manual or hydraulic, and they're in stock and ready to ship.

Shop all bender dies →

Want a head start? See our common die packages. Not sure which radius you need? Read the CLR guide or call us at (805) 239-5972.

Customers Also Bought

     American-Made Fabrication Tools 

    JMR Manufacturing is a family-owned company built in Paso Robles, CA. We design and manufacture fabrication tools right here in the USA — built to the standard we'd want in our own shop. Questions or custom orders:

    (805) 239-5972 · info@jmrmfg.com