American-Made Tube Benders
JMR tube benders are built for round tube, square tube and pipe up to 2-1/2" OD in mild steel, chromoly, stainless and aluminum. Manual tube benders from $375 or hydraulic tube benders from $1,295.
- Made in the USA
- In stock, ready to ship
- Every JMR die fits every JMR bender
Start with a manual tube bender, upgrade anytime
Add air or electric hydraulics later. Your bender and dies carry over.
Upgrade kits →100's of bender dies in stock
Round tube, pipe and square, 1/2" to 2-1/2". Centerline options from 3" to 8".
Shop dies →Our benders never go obsolete
Same geometry since 2002. A JMR bender from then takes the dies we make today.
Our story →Let customers speak for us
Which JMR tube bender is right for you?
Every JMR tube and pipe bender uses the same bender head, built in Paso Robles, California, so every JMR die set fits every JMR bender. The difference is the drive. Manual benders bend up to 2" x .120" wall by hand and can be upgraded to hydraulics later. Hydraulic benders bend up to 2-1/2" OD and 2" x .250" wall without the pulling, and the auto stop model adds a set angle for production runs.
Compare JMR tube benders
| Spec | RaceLine Manual | Manual (TBM-250) | Air/Hydraulic | Electric/Hydraulic (TBH-250) | Electric/Hydraulic w/ Auto Stop |
|---|---|---|---|---|---|
| Price | $375 | $475 | From $1,295 | From $2,795 | $4,995 |
| Best for | First bender, tight budget | Regular shop use by hand, room to upgrade | Heavy wall, faster cycles, shops with air | Hydraulic power without shop air | Production runs, repeat angles |
| Drive | Manual, 3 speeds | Manual, 5 speeds | Air-over-hydraulic foot pump, 90 PSI | Electric-over-hydraulic, 110V | Electric-over-hydraulic, 110V |
| Round tube | Up to 2" x .120" by hand | Up to 2" x .120" by hand | Up to 2-1/2" x .120" | Up to 2-1/2" x .120" | Up to 2-1/2" x .120" |
| Heavy wall | With hydraulic upgrade | With hydraulic upgrade | 2" x .250" mild steel | 2" x .250" mild steel | 2" x .250" mild steel |
| Square tube | Up to 2" x .120" by hand | Up to 2" x .120" by hand | 2" x .250" mild steel | 2" x .250" mild steel | 2" x .250" mild steel |
| Pipe | Up to 2" pipe | Up to 2" pipe | 2" Schedule 40 | 2" Schedule 40 | 2" Schedule 40 |
| Full 90° bend | Re-pin required | One pass, no re-pin | One stroke with optional 90° cylinder | One stroke with optional 90° cylinder | One stroke, about 20 seconds |
| Materials | Mild steel, DOM, 4130 chromoly, stainless and aluminum | ||||
| Bend capacity | 180° | 180° | 180° | 180° | 180° |
| Finish | Uncoated arms and rack | Powder coated | Powder coated | Powder coated | Powder coated |
| Hydraulic upgrade | Yes, any time | Yes, any time | Hydraulic | Hydraulic | Hydraulic |
| Shipping weight | 45 lb | 50 lb | 110 lb | 240 lb | 250 lb |
| Die sets | All JMR tube, pipe and square die sets fit all five benders. Sold separately. | ||||
| Made in | Paso Robles, California, USA | ||||
Capacities are for mild steel unless noted and vary with material hardness. See our capacity charts for every size and wall.
Frequently asked questions
Should I buy a manual or hydraulic tube bender?
If you bend up to 2" x .120" wall a few times a week, a manual bender does the job. If you bend heavy wall, 2-1/2" tube, or the same part over and over, hydraulic saves time and effort. If you're not sure, start manual. Every JMR manual bender can be upgraded to hydraulic later.
How much can I really bend by hand?
We rate our manual benders by what an average person can realistically pull, not by what the frame can survive. That's 2" OD x .120" wall round tube and 2" x .120" wall square tube. The frame is the same as our hydraulic benders, so heavier wall is possible with a hydraulic upgrade.
Do all JMR dies fit all JMR benders?
Yes. Every JMR tube, pipe and square die set fits every JMR bender, so your dies move with you if you upgrade. Dies are sold separately so you only buy the sizes you need.
Can I upgrade my manual bender to hydraulic later?
Yes, at any time. The Air/Hydraulic and Electric/Hydraulic upgrade kits bolt on and raise capacity to 2-1/2" OD.
Can I bend exhaust tubing?
JMR benders are rotary draw benders built for roll cages, chassis, handrails, racks and structural work. Large-diameter, thin-wall exhaust tubing needs a mandrel bender to bend without wrinkling.
Can JMR help me choose a bender?
Yes. Call (805) 239-5972 or email info@jmrmfg.com with your material, tube size, wall thickness and how many parts you bend, and we'll point you to the right setup.
Looking for a full setup?
If you're outfitting a shop rather than buying just a bender, our fabrication stations and packages put a bender, dies and mounting together in one order.